- 您现在的位置：买卖IC网 > Sheet目录960 > ALQ324 (Panasonic Electric Works)RELAY GEN PURPOSE SPST 10A 24V
LQ (ALQ)
NOTES
Usage, transport and storage
conditions
1) Temperature:
–40 to +85 ° C –40 to +185 ° F
2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage
Humidity, %RH
85
Tolerance range
Solder and cleaning conditions
1) Please obey the following conditions
when soldering automatically.
(1) Preheating: Within 120 ° C 248 ° F
(solder surface terminal portion) and
within 120 seconds
(2) Soldering iron: 260 ° C ± 5 ° C
500 ° F ± 41 ° F (solder temperature) and
within 6 seconds (soldering time)
2) Do not use ultrasonic cleaning. This
will adversely affect relay characteristics.
When cleaning the relay, please use
alcoholic solvents.
Cautions for use
1) For precautions regarding use and
explanations of technical terminology,
please refer to our web site.
When highly frequent opening and
closing of the relay is performed with a
load that causes arcs at the contacts,
nitrogen and oxygen in the air is fused by
the arc energy and HNO 3 is formed. This
can corrode metal materials.
Three countermeasures for these are
listed here.
? Incorporate an arc-extinguishing circuit.
? Lower the operating frequency
? Lower the ambient humidity
5) This value can change due to the
switching frequency, environmental
conditions, and desired reliability level,
therefore it is recommended to check this
with the actual load.
6) Heat, smoke, and even a ?re may
(Avoid freezing
when used at
(Avoid
condensation
(panasonic-electric-works.net/ac)
occur if the relay is used in conditions
temperatures
lower than
0 ° C 32 ° F )
5
when used at
temperatures
higher than
0 ° C 32 ° F )
2) To ensure good operation, please keep
the voltage on the coil ends to ± 5% (at
20 ° C 68 ° F ) of the rated coil operation
outside of the allowable ranges for the
coil ratings, contact ratings, operating
cycle lifetime, and other speci?cations.
–40
–40
0
+32
Temperature, ° C ° F
85
+185
voltage. Also, please be aware that the
pick-up voltage and drop-out voltage may
Therefore, do not use the relay if these
ratings are exceeded.
change depending on the temperature
7) If the relay has been dropped, the
4) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
5) Freezing
Condensation or other moisture may
freeze on the relay when the
temperatures is lower than 0 ° C 32 ° F . This
causes problems such as sticking of
movable parts or operational time lags.
6) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
and conditions of use.
3) Keep the ripple rate of the nominal coil
voltage below 5%.
4) The cycle lifetime is de?ned under the
standard test condition speci?ed in the
JIS C 5442 standard (temperature 15 to
35 ° C 59 to 95 ° F , humidity 25 to 75%).
Check this with the real device as it is
affected by coil driving circuit, load type,
activation frequency, activation phase,
ambient conditions and other factors.
Also, be especially careful of loads such
as those listed below.
(1) When used for AC load-operating and
the operating phase is synchronous.
Rocking and fusing can easily occur due
to contact shifting.
(2) Highly frequent load-operating
appearance and characteristics should
always be checked before use.
8) Incorrect wiring may cause
unexpected events or the generation of
heat or ?ames.
ASCTB92E 201206-T
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e/
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ALTS3125
RELAY GEN PURPOSE SPST 5A 12V
ALZ51F18
RELAY GEN PURPOSE SPST 16A 18V
AMC1204EVM
EVAL MODULE FOR AMC1204
AO241R
RELAY SSR 1A SIP DC
APF10312
RELAY GEN PURPOSE SPST 6A 12V
APSRM2
REMOTE MODULE FOR APS INVERTER
APSRM4
REMOTE CONTROL MODULE FOR APS/PV
APSRM
REMOTE SWITCH FOR APS INVERTER
相关代理商/技术参数
ALQ35F48
功能描述:DC/DC转换器 DC-DC 1-OUT 3.3V 35A 144W 8-Pin 1/4-Brick RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
ALQ35F48N
功能描述:CONV DC-DC 144W 48VIN 3.3V NEG RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:ALQ35 产品目录绘图:V(R,7)AH Series 标准包装:25 系列:V7AH 类型:非隔离（POL） 输出数:1 电压 - 输入（最小）:3V 电压 - 输入（最大）:5.5V Voltage - Output 1:1.8V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:12A 电源（瓦） - 制造商系列:21W 电压 - 隔离:- 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:5-SIP 模块 尺寸/尺寸:0.70" L x 0.31" W x 0.65" H（17.8mm x 7.9mm x 16.5mm） 包装:管件 工作温度:-40°C ~ 85°C 效率:87% 电源（瓦特）- 最大:21.6W 其它名称:507-1141-5
ALQ3F12
功能描述:General Purpose Relay SPST-NO (1 Form A) 12VDC Coil Through Hole 制造商:panasonic electric works 系列:ALQ 包装:管件 零件状态:有效 继电器类型:通用 线圈类型:无锁存 线圈电流:16.7mA 线圈电压:12VDC 触头外形:SPST-NO（1 A 型） 额定接触（电流）:10A 开关电压:250VAC - 最大 导通电压（最大值）:9 VDC 关闭电压（最小值）:0.6 VDC 工作时间:20ms 释放时间:20ms 特性:绝缘 - F 类 安装类型:通孔 端子类型:PC 引脚 触头材料:银镍（AgNi） 线圈功率:200 mW 线圈电阻:720 欧姆 工作温度:-40°C ~ 85°C 标准包装:100
ALQ3F24
功能描述:General Purpose Relay SPST-NO (1 Form A) 24VDC Coil Through Hole 制造商:panasonic electric works 系列:ALQ 包装:管件 零件状态:有效 继电器类型:通用 线圈类型:无锁存 线圈电流:8.3mA 线圈电压:24VDC 触头外形:SPST-NO（1 A 型） 额定接触（电流）:10A 开关电压:250VAC - 最大 导通电压（最大值）:18 VDC 关闭电压（最小值）:1.2 VDC 工作时间:20ms 释放时间:20ms 特性:绝缘 - F 类 安装类型:通孔 端子类型:PC 引脚 触头材料:银镍（AgNi） 线圈功率:200 mW 线圈电阻:2.88 千欧 工作温度:-40°C ~ 85°C 标准包装:100
ALQ40
制造商:EMERSON-NETWORKPOWER 制造商全称:Emerson Network Power 功能描述:High Efficiency Quarter Brick
ALQ40_03
制造商:ASTEC 制造商全称:Astec America, Inc 功能描述:Industry Standard Brick: 36V-75V Input / 50A Output Current
ALQ40F48
制造商:EMERSON-NETWORKPOWER 制造商全称:Emerson Network Power 功能描述:High Efficiency Quarter Brick
ALQ40F48-L
功能描述:DC/DC转换器 DC-DC 1-OUT 3.3V 40A 132W 8-Pin 1/4-Brick RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: